Use of Solubility Parameter to Design Dry Suspension of Cefaclor as a Dual Pack System

Indian Journal of Pharmaceutical Sciences 609 September October 2008 Cefaclor, an orally active cephalosporin in clinical practice, belongs to the group of -lactam antibiotics. It is a slightly water soluble drug and its antibacterial activity is dependent on the presence of -lactam functionality that can be hydrolyzed under aqueous conditions1. Solubility and stability problems of cefaclor can be overcome by selection of a suitable co-solvent. One important concept of solubilization by co-solvents is the polarity scale, which includes surface tension, solubility parameter, dielectric constant and partition coefficient to express the polarity of the solvents2. The choice of an appropriate co-solvent is important to obtain maximum solubility of the drug and solubility parameter serves as a guide in the selection of appropriate co-solvent3,4.

Cefaclor, an orally active cephalosporin in clinical practice, belongs to the group of -lactam antibiotics.It is a slightly water soluble drug and its antibacterial activity is dependent on the presence of -lactam functionality that can be hydrolyzed under aqueous conditions 1 .Solubility and stability problems of cefaclor can be overcome by selection of a suitable co-solvent.One important concept of solubilization by co-solvents is the polarity scale, which includes surface tension, solubility parameter, dielectric constant and partition coefficient to express the polarity of the solvents 2 .The choice of an appropriate co-solvent is important to obtain maximum solubility of the drug and solubility parameter serves as a guide in the selection of appropriate co-solvent 3,4 .
The use of single mixture limits the polarity range while the binary mixture with a common co solvent allows to expand the polarity range and to test the influence of the co solvent on drug solubility 5 .Evaluation of solubility parameter in different solvent blends of various polarities provides an important insight into the solubility of drug.The aim of the present study is to determine the solubility parameter of cefaclor by evaluating the solubility of cefaclor in different blends of water:propylene glycol (PG) to overcome the problem of solubility and hydrolytic instability, and to design and formulate dry suspension for reconstitution of cefaclor as a dual pack system and compare with marketed formulation.

MATERIALS AND METHODS
Cefaclor was obtained as gift sample from Siemens Laboratories, Gurgaon, India and Himedia dialysis membrane-50 was procured from Himedia Lab.Pvt. Ltd., Mumbai.Polyplasdone XL was a gift sample from ISP Technologies Inc., NJ. Methyl cellulose, microcrystalline cellulose, acacia gum and sodium citrate were obtained from Ranbaxy Fine Chemicals Ltd., New Delhi, and sodium benzoate, sodium starch glycolate, sucrose from Qualigens Fine Chemicals, Mumbai.The binary mixtures were prepared (by volume) with glycerin or propylene glycol (Ranbaxy Fine Chemicals Ltd., New Delhi) and all glass double distilled water.

Solubility measurements:
Sealed flasks containing an excess of cefaclor in the pure solvents and solvent blends were shaken at 370.5 0 in a temperature controlled water bath (Hicon, India).When the saturation concentration was attained (after 72 h), the solid phase was removed by fi ltration through nylon fi lter disk (0.45 ).The clear solutions were diluted with double distilled water and assayed in a double-beam spectrophotometer (Shimadzu Pharmaspec, UV-1700, Japan).The spectrophotometric measurements were performed at 264 nm.The densities of the solutions were determined at 370.5 0 in 10 ml pycnometer to convert molar solubility into mole fraction units 6 .All the experimental results are the average of at least three replicated experiments.The coefficient of variation (SD/mean100) was within 2% among replicated samples for the solubility measurements.

Solubility parameter determination:
Solubility parameter determination of cefaclor ( 2 ) was done by solubility measurement method (experimental method) and by theoretical methods namely molar volume method and by method proposed by Lin and Nash 6 .In solubility measurement method, the solubility parameter of cefaclor is assumed to be similar to that of the solubility parameter of the solvent ( 1 ) in which the drug exhibits maximum solubility 7 .Hence, the solubility data (Table 1) obtained by the method described in preceding section was used to determine  2 .
The solubility parameter of cefaclor was determined by molar volume method by calculating the mole fraction solubility (X i 2 ) of cefaclor in solvent blends containing water and propylene glycol in different ratios as shown in Table 1.The mole fraction solubility was calculated by using the following equation, X i 2 = n 2 /n 1 +n 2 (1), where n 1 = number of moles of solvent and n 2 = number of moles of solute.A plot of mole fraction solubility of cefaclor in the various ratios of the binary mixtures was made against Δ ( 1 - 2 ) .The solubility parameter of the solvent blend ( 1 ) in which cefaclor showed peak mole fraction solubility represented the solubility parameter of cefaclor ( 2 ) 8 .
The method of Lin and Nash is based on the use of experimental mole fraction solubility of drug in given solvent blends.Thus  2 can be determined by use of the following equation, is the mole fraction solubility of the solute in a given solvent and δ 1 is the solubility parameter of the solvent 9 .

Formulation of dry suspension of cefaclor for reconstitution:
Dry suspensions for reconstitution were prepared using the formulae shown in Table 2.All the ingredients were mixed in geometric proportion in a glass pestlemortar and a suffi cient volume of granulating agent (starch paste, 5% w/v for F1-F5 and alcohol 95%  q.s.q.s.q.s.q.s.q.s.q.s.q.s.q.s.q.s.q.s.q.s.q.s.q.s.q.s.Flavor (orange) q.s.q.s.q.s.q.s.q.s.q.s.q.s.
v/v for F6 and F7) was incorporated slowly.After enough cohesiveness was obtained, the mass was sieved though mesh #16.The granules were dried in oven (Jindal, Scientifi c Inst.Pvt. Ltd., India) at 60° for 30 min and the dried mass was passed through mesh #22.The dry products were reconstituted with reconstitution medium (water: propylene glycol, 20:80) for further evaluations.

Evaluation of reconstituted suspensions:
The pH of the reconstituted suspensions was measured using pH meter (DB-1011, HICON, India).The sedimentation volume (H u /H o ) calculated against time was described in terms of the ratio of equilibrium settled height (H U ) to original height (H o ) 10 .The degree of fl occulation was determined as the ratio of sedimentation volume of the fl occulated suspension to the sedimentation volume of deflocculated suspension 11 .Ease of redispersion of suspensions was quantified by counting the number of strokes (given at an angle of 180 0 ) required to redisperse the dispersed phase in 10 ml of the sample 12 .For single point viscosity determination of the reconstituted suspension, Brookfi eld viscometer (DV-II, Brookfi eld Eng.Lab.INC, USA), attached with spindle RV No. 4 was used.Suspension (75 ml) was taken in 100 ml beaker and the viscosity was measured at 100 rpm at room temperature.For drug content determination 1 ml of each suspension was dissolved in 100 ml of double distilled water, filtered, diluted as required and analyzed spectrophotometrically at 264 nm.Each value represents the mean content of three replicates 13 .
In vitro drug release study: Reconstituted suspension (5 ml) was taken in the donor compartment of lab fabricated glass diffusion cell (d= 2.4 cm) and 50 ml of double distilled water in the receptor compartment was stirred at 100 rpm and maintained at 37±0.5 0 .The HIMEDIA dialysis membrane-50 soaked in double distilled water for 24 h was used as a barrier membrane.Samples were withdrawn at different time intervals of 15, 30, 60, 90, 120, 150, 180, 240 and 360 min diluted with double distilled water and analyzed spectrophotometrically at 264 nm with reference to suitably constructed calibration curve.Release study was performed in triplicate.Marketed formulation (Kefl or ® , Ranbaxy, India) was also evaluated for in vitro drug release and compared with the best formulation.

RESULTS AND DISCUSSION
Solubility of cefaclor was evaluated in solvent blends containing water:PG for the determination of  2 as the varying blends of these provided a range of 14.80 -23.40 (Cal/cm 3 ) 0.5 of  1 .The peak solubility (X 2 ) of 29.93 mg/ml for cefaclor was observed in a solvent blend of water: PG (20:80) with  1 of 16.52 (Cal/cm 3 ) 0.5 .Thus the solubility parameter for cefaclor can be defi ned as 16.52 (Cal/cm 3 ) 0.5 as according to the solubility measurement method,  2 is that value of  1 at which the drug exhibits maximum solubility.Table 1 lists the solvent blends, the Hildebrand solubility parameter ( 1 ) of the solvent blends and the experimentally determined solubilities (mg/ml) of cefaclor.
The molar volume method was used to determine the peak mole fraction solubility of cefaclor in various solvent blends and the mole fraction solubilities X i 2 of cefaclor and Δ are tabulated in Table 1.Peak mole fraction solubility was determined to be 3.51×10 -3 in solvent blend (water:PG, 20:80) with  1 value 16.52 (Cal/cm 3 ) 0.5 , which is in agreement with solubility measurement method.A plot of  1 and X i 2 (fig. 1) showed a bell shaped curve suggesting that both at lower and higher values  1 = 16.52 (Cal/cm 3 ) 0.5 the solubility of cefaclor decreased.When Δ was plotted against X i 2 (fi g. 2) , the solubility parameter of cefaclor was confi rmed at 16.52 (Cal/cm 3 ) 0.5 as it is that value of  1 at which cefaclor exhibited peak mole fraction solubility and Δ = 0.  2 determined by the method of Lin and Nash were found to be 16.35 (cal/cm 3 ) 0.5 , which is comparable to the value obtained by solubility measurement method and molar volume method.

Fig. 1: Solubility parameter versus mole fraction solubility profi le of cefaclor by molar volume method
Granular formulations of dry suspension for reconstitution were designed based on of two types of disintegrants, gel forming (methyl cellulose and sodium starch glycolate) and non-gel forming (microcrystalline cellulose and polypasdone XL) in order to assess their role on drug release (Table 2).Table 3 summarizes the physical and rheological characteristics of the reconstituted suspensions.The pH was found to be the range of 3.74-3.82,which is desirable for the stability of cefaclor 14 and also accenuates palatability of the oral dosage form.The formulation F7, that showed maximum value (0.89 closest to 1 as compared to other formulations) of sedimentation volume and degree of fl occulation is suggested to be homogenous in appearance and may not exhibit caking on long term storage.The viscosity of all the formulations ranged between 42-56 cps.
The release profiles of the freshly reconstituted suspensions are reported in fi gs. 3 and 4. The order of percentage cumulative drug release (%CDR) at 360 min is F7>F6>F5>F4>F1>F2>F3 with values of 64.14, 58.74, 53.48, 48.33, 44.50, 37.08, 32.51, respectively.In formulations F1, F2 and F3 a decrease in %CDR was observed as the concentration of gel forming disintegrants increased irrespective of the amount of the suspending agent used whereas in formulations F4 and F5, an increase in %CDR drug release was observed with increasing amounts of non-gel forming disintegrants.In an attempt to enhance the %CDR, granular formulations containing superdisintegrant

TABLE 1 : SOLUBILITY OF THE BINARY MIXTURE BLENDS
The binary mixture blends, δ 1 and δ 1 -δ 2 and the corresponding values of equilibrium experimental solubility and mole fraction solubility